Why Fit Matters for a Wearable Pump
A properly fitted flange is one of the most important factors for comfortable and effective pumping. When the flange tunnel is too large, your nipple may be pulled unevenly, causing discomfort or reduced milk output. That’s where flange inserts come in.
The BabyBuddha 15mm Flange Inserts are designed to reduce the opening of a standard 24mm EasyFit Flange, giving you a smaller, more precise fit. This can help improve comfort, reduce friction, and support better nipple alignment during pumping.
Who Should Consider 15mm Inserts
If you measure your nipple diameter at around 15mm (or slightly less), a 15mm flange insert may be your best fit. Rather than replacing your entire flange set, these inserts let you customize your existing 24mm flanges for a more comfortable session.
The inserts are compatible with BabyBuddha 2.0 and 3.0 pumps when used with 24mm EasyFit Flanges. They work with both portable and wearable pump setups, giving you flexibility without needing a separate flange collection.
15mm Flange Inserts at a Glance
- Flange Inserts – 15mm (2-pack) for Wearable Breast Pump and 24mm Flanges: Achieve a better fit for a more comfortable, effective pump session using 15mm Flange Inserts designed for BabyBuddha pumps. A correct fit can reduce discomfort and help you express milk more effectively, making pumping sessions more productive.

Flange Inserts – 15mm (2-pack) for Wearable Breast Pump and 24mm Flanges - Flange Inserts – 15mm (2-pack) for Wearable Breast Pump and 24mm Flanges: Helps improve comfort and reduce friction during pumping, and supports better nipple alignment for more effective milk removal. Less friction means less irritation, while proper alignment helps your pump work as intended.
- Flange Inserts – 15mm (2-pack) for Wearable Breast Pump and 24mm Flanges: Compatible with BabyBuddha 2.0 and 3.0 Pump when used with 24mm EasyFit Flanges. You can upgrade your fit without buying a whole new flange kit, saving money and reducing waste.
How to Check Fit and Insert the 15mm Flange Inserts
Before using the inserts, confirm that your nipple diameter is close to 15mm. A simple ruler or measuring tape can help. The insert should fit snugly around your nipple without compression or gap.
To insert:
Place the 15mm insert into the tunnel of your 24mm EasyFit Flange. The soft, flexible material should sit flush against the flange wall. Press gently until it is fully seated. There should be no folds or gaps.
Attach the flange to your BabyBuddha pump as usual. During pumping, check that your nipple moves freely within the insert without rubbing the sides. If you feel pinching or your nipple touches the tunnel wall, the fit may still be off.
- Measure your nipple: Measure the diameter at the base (not the tip) after a few minutes of pumping or gently stimulating. This gives a more accurate size.
- Insert the 15mm insert: Gently push the insert into the 24mm EasyFit Flange until it is fully seated. The insert should be centered and smooth inside.
- Check during pumping: Your nipple should move back and forth without rubbing the sides. If it touches, try a different size or adjust the insert position.
Cleaning and Care for Long-Lasting Inserts
Keeping your flange inserts clean is straightforward. After each use, wash them with warm, soapy water and allow them to air dry. The inserts are also safe for standard sterilization methods, making them easy to maintain.
Because the inserts are soft and flexible, handle them gently during cleaning to avoid tearing. Replace them if you notice any cracks, stretching, or changes in fit, as this can affect suction and comfort.
A Note on Compatibility
The 15mm Flange Inserts are designed specifically for BabyBuddha pumps with 24mm EasyFit Flanges. They are not intended for use with other flange sizes or pump brands unless compatibility is confirmed. If you are unsure whether your flange accepts inserts, check the flange model or contact BabyBuddha support.
Using the correct insert size is the key to a comfortable pumping experience. If 15mm is your best fit, these inserts provide a simple way to customize your setup without replacing your entire flange.


